-
How to remove moisture inside Goal Zero Lighthouse Micro
I left my lighthouses outside while it's raining heavily last night. Later, I found out that there is some moisture inside my lighthouses. How can I remove those moisture/water inside the lighthouses?
-
Can you hook up the Escape Remote Display to a larger monitor?
I have an Escape Remote Display hooked up to my Yeti Pro 4000, but I was wondering if there was any way I could get the display hooked up to a larger monitor. For my uses, I cannot connect via bluetooth and wifi. Thank you for any assistance/advice.
-
Time to Empty Calculation.
Shouldn't this read 7 days 12 hours instead of 2 days 3 hours? Am I missing something in here?
-
Won't charge despite rebooting
I have a 3000x with firmware 1.8.9. It once failed to charge so I found out that rebooting by pressing the button with green circle under the lid and "info" button simultaneously reboots the unit and allows you to charge. It worked. But, now it won't work. Actually, I'm not even sure it rebooted this time since it doesn't…
-
Yeti Pro 4000 - Tank Pro 4000 question
An alert message appeared this morning on my Yeti Pro 4000 "Battery cell UVP" and the Tank Pro 4000 error light is flashing. How to I resolve???
-
What is the latest Firmware update and did it fix Pro 4000 bugs?
-
Yeti 3000X - Need a repair center or replacement inverter?
The inverter on my 3000x have stopped working. Do I have any route to purchase a replacement inverter or get it repaired?
-
How to Ground a Yeti 1500
I am trying to just use my goal zero to maintain my Tesla battery but the car gives me "inadequate grounding error". How can I ground my 1500x?
-
Connecting/disconnecting 8mm cords is very difficult, especially when cold. Any tips/hacks?
-
Brand new GZ Yeti 4000 Pro, multiple problems right from the start?
Ok wow, where to begin? Well, I just got and unboxed my new GZ Yeti 4000 Pro today and plugged it in, linked it to the app on my phone, all per provided instructions and almost NOTHING is working! The unit powers on and does connect both directly and "cloud connects". My first order of business was a check for any…
-
Yeti 400 Pro Grounding
Yeti 4000 Pro. Have solar input through the HPP port. Solar panels are mounted in back yard and are grounded to each other (strung in series) and then the last panel to an 8 foot deep grounding rod. Resistance out is less than 5 Ohms. Using 10awg copper grounding wire out there. Inside, the Yeti 4000 Pro is connected to a…
-
Mix & Match Panels (Goal Zero & Off Brand)
I have a Yeti 1400 Lithium, MPPT module, a pair of Nomad 200 panels and a 120W 3rd party panel. What I would like to do is run the Nomad panels through the MPPT module and the off brand panel through the Yeti's built charge ports. I can't find anything that would suggest this is a bad idea, but figured I'd double check.…
-
Battery Recycling
I have an old Yeti 50 and 400 that it looks like some of the cells have shorted. The 50 gives about 2 minutes of charge and the 400 isn't much better. I have cycled them a couple of times and the run time hasn't gotten any better. Is there a suggested procedure for recycling these since I believe they are lead acid.
-
New Yeti500X charging?
I wonder if my new Yeti500X is charging or not. It is connected to 230V from a wall-outlet (now on 3rd hour). The blue input LED is lit. On the display the 20%-battery-segment flashes. (Very slowly: 4 per minute). But the display shows Input 0 watts. I tried to reset; no change. Is this normal?
-
Nomad10 or nomad5
Hi, I'm a trekker and I'm looking for a solar panel I can use for multidays trekking. I can't make a choice between Nomad 10 or 5. For me it's important don't have so much weight to carry on but at the same time I'd like to be able recharge my camera or phone easily. Can you give an advice based on your own experiences.…
-
Chaining yeti 400s
I have two lead acid yeti 400s, and wish to chain them together with the anderson chaining port. I belive that if i charge one it will charge both units, however would I be able to charge both simultaneously while chained together? Could i plug solar panels into one unit and the car charger into the other unit while…
-
Wifi off after outage I'm traveling
I'm currently in Thailand and we had a 15+ hour power outage at home in California. Power is back on but I cannot access my yetti 3000x as the software turned off the wifi (to save power). I had the Yeti in hot stand by running the frig, freezer and 2 lighting circuits. Now there is no way for me to know the status of the…
-
Car Charger for the Yeti 700
Is this the correct 12V car charger for the Yeti 700? https://www.goalzero.com/collections/vehicle-accessories/products/yeti-12v-car-charging-cable
-
Sherpa 100 Issues
Purchased a Sherpa 100AC (older generation) in March of 2023. It now won’t hold a charge. Shows 99% but discharges immediately and shuts off when a device is plugged in. Have reset etc., to no avail. In addition, even though I’ve configured the ports for In and Out only vs Auto, the Sherpa will actually discharge my…
-
Yeti 3000X and vacuum
Can you run a Shark Vacuum off of a Yeti 3000X? Says it is a 1200W vacuum (10Amps @ 120V). https://www.sharkclean.com/products/shark-navigator-lift-away-deluxe-upright-vacuum-zidNV360
-
Yeti Pro 4000 SOC Inaccuracy
I suspect that the Yeti Pro 4000 is mis-reading its own state of charge. I observed my Yeti drain down to zero (super-low voltage) even though the SOC read 85%. I have it on battery saver mode so it should have stopped delivering power at 15%, yet it continued until it was fully drained. Even after I jump-started it the…
-
20kwh
So I just bought the 20kwh home backup and it works great. I have a smart plug hooked up to charge/passthrough during off peak hrs and have my house run on it during peak hours. That being said I want to add Solar panels now to minimize my reliance in PG&E. While I love the GZ panels this is home back up and the panels…
-
Yeti 700 AC port trips as soon as anything plugged in
My new yeti 700 worked great for a few weeks, now the AC port trips to red as soon as anything is plugged in to it. Anyone else have this issue? The reset comman list I found on this site does not list the 700, so unsure how to reset it? TIA-
-
Yeti 700 Charging Issue
A few days ago, I took delivery of a Yeti 700. I charged it overnight, via a wall outlet, to 100%. The following day, I noticed it had dropped to 96% while still plugged in. The unit had nothing plugged into it to draw any current. I contacted tech support and was told to reset the unit, discharge the battery then…
-
Fully off grid compatible?
Has anyone used the Yeti Pro 4000 as their only off grid electrical source? We are currently wiring our yurt to run off the Yeti Pro with the Haven 10 but we're running into issues of finding information of how to hook up everything without wiring it to a breaker panel. Any and all information would be helpful!
-
AC outlet has no power
Hi! Bought a 3rd hand van with a Yeti 3000X (no receipt or warranty). Worked a charm the last 6 months but suddenly the AC outlet has no power. I've tried all the resets to no avail. There are no errors or loud beeps, the only thing I have noticed which may or may not be new is when I press the AC button above the port…
-
Link Expansion Module LEDs flashing green then red
Hi all, I think I have some issues with my Link since the last firmware update. My LEDs are flashing red/green, but not all 4 as described in the table I have seen either 1 or 3 LEDs flashing. What could this mean? Also, I have no notification in the app, which makes it very hard to spot problems since my setup is in my…
-
Charging profile scenarios for home backup
I have the Yeti PRO 4000 + Haven 10 + 3600 Passthrough cable installed for emergency home backup. I particularly wanted the automatic power switching (APS) in the event of a power outage while I am away for a few weeks at a time. The charging profile is set to Performance (min=0%, recharge=95%, max=100%). Two questions: 1)…
-
Yeti Pro 4000 Nominal Voltage
So, I had an incident recently where, after sitting unused for a few days my Yeti 4000 started beeping with the CHGMONERR warning. There was also an alert telling me there was a battery fault. The only way I could get the unit to power on was to plug the AC charging cable into the back of the unit. Even with it plugged in…
-
Help Identifying Correct 12V Plug for DC Output on Original Sherpa 100
I could use some help identifying the correct plug for the 12V DC output on my original Sherpa 100 so that I could find a plug to make my own DC power cables for this power station. Thank you for your help. I've attached an image to help clarify which port I'm interested in identifying the correct plug for. Thanks!