-
Advice on setup
I just bought a yeti 6000x. I would like to set it up with solar panels and connect it thru an integration kit. All i have now is the 6000x. I need advice on what to get. Im eyeing on reusing an old set of panels. I have 4 sharp panels at 140w each, 24.85v 7.85w, using mc3. I was thinking of doing a series-parallel to…
-
GZ 1500X - charging with Renogy 100w panels
I just got my first Goal Zero product - the 1500X power station, which I really like and intend to rig it up with the Home Integration Kit to provide emergency power (perhaps ultimately with additional Tank batteries). Now, I would like to recharge it with some panels that I already own, that is Renogy 100w panels. These…
-
Yeti150
I had a battery go bad in my goal zero yeti 150. Replaced the battery. Now it goes from full to drained in a day. Why?
-
The plastic cases of my lamp is going sticky
Hi, can anyone help please. The plastic case of my Goal Zero Lighthouse has gone all sticky. Can anyone please tell me why. It is awful to touch as the stickiness gets on your hands.
-
Charging station for Escape 30 (out of production)?
Hi! I have an older Escape 30 briefcase charging panel. As is, the charging cord is a smaller yellow circle connector. Is there a current Goal Zero (or other brand) charging station compatible with this plug? If not, does anybody offer a yellow circle to 8mm blue circle adapter? Thanks!
-
Available Solar Panels for my Yeti 150
It appears all the panels are discontinued for this early model. What are my options now? Would like a flexible 100 watt panel if available .
-
Why does out Solar causes our output to fluctuate.
Hi there, we have found that when we plug in our solar panels into our Yeti 3000x that it sometimes causes our input and output to fluctuate quite a lot. The screenshots were taken from a video a couple seconds apart, I would upload the video but it’s too large. This seems to happen more often when we are getting a larger…
-
Regarding Yeti1000X
I have a Yeti100X that is plugged in but is not charging. It is at 47%. I have tried unplugging and plugging back in. It is in an unheated garage that is about 40* F. It was purchased 8/22 from Costco. What should I do?
-
Initial Charging Of A New Sherpa 100PD?
I just received my new 100PD (prev gen) today, and plugged it up to charge. The charger I'm using is a PowerPort 2 Elite, model # A2023, usb A to usb C. Output shows to be 5.0V, 2.4A. I'm starting to wonder if there is a problem. When I plug it up, the power level display on the 100PD comes on, displaying two zeros. The…
-
Research. Anyone know if the x1500 is compatible with lensun flexible solar panels?
-
Goal Zero Yeti150
I have two of them and they bouth make be-ping sound right after I take them of the charge from wall outlet. I bought them for 200$ each, now I see they are only 100 . what should I do,I know is not wort to repair them but I feel bed to trough them in garbige. Can you help me with idea what to do.
-
Can I safely charge a Flip 36 on a Nomad 100?
Will any of the power bank items be damaged by charging them with higher output devices? For example the maximum output of a Nomad 100 is much higher than the max input of the Flip 36. Would than cause any short or long term damage to the Flip 36?
-
Can i connect more than 600w of panels to my yeti 6000x app port rated at 600w?
Id like ask if its ok to series parallel panels beyond the 600w on the yeti 6000x app port (rated 600w). I plan to do parallel 3 sets of 2 140w 7.8A 24v panels. Series 2, 140w, 7.8A, 24v = 280W, 7.8A, 50v Having 3 in parallel gets to, 840w, ~24A, 50V The APP port on the goal yeti 6000 is 600W, 50V, 50A. My thinking is that…
-
Yeti 500x and 400Li have much different output voltages. Why?
My 500x and 400Li have much different output voltages when fully charged. The 500x indicates 13.44v and the 400Li 12.4v, when both measured using two identical dual USB/USB-C car chargers with LED display, rotated between power stations. Am I correct in assuming that the output voltage indicates state of charge (SOC)? If…
-
Can these power stations be charged by a windmill?
-
Normal behavior of Boulder 200bc - experience
I recently got myself a Yeti 3000X bundled with the Boulder 200 Briefcase, but we didn't have a fully sunny day since then to observe the Boulder's full performance. Since I'm new to solar and all, I'm wondering about what I could expect. So far I can observe the following: With a cloudy sky (even bright diffuse light…
-
YETI Link expansion Module
I have the Yeti Link installed on my 1400 and 2 expansion batteries attached. It is plugged into the wall. The input light is on and only one green light is lit. It is not blinking, so am I to infer that it is not charging. Any suggestions
-
The Little Things
Haven’t tried the product yet, but made two orders. First concern is that I received FedEx tracking numbers linked to the UPS tracking system on both orders. Second concern is I ordered a package with 2 Boulder suitcases. A package with no way to link the two solar units just seems cheap. Hence the second order. If the…
-
Charging Lighthouse Core & Lighthouse 600
I looked on the product page, and in the user manuals. I seem to be finding conflicting/omitted information though. For the Lighthouse Core & Lighthouse 600 is it recommended, or acceptable, to leave these plugged in when not in use? The web page for the Core says to leave plugged in on the "shelf life" info, but the page…
-
My Yeti3000x stopped charging!
My Yeti3000x just suddenly stopped charging. I purchased a replacement sherpa charging cord, but it still isnt charging. Any suggestions?
-
Where can I get a manual or instructions for the 1250?
I havent used my 1250 yet and have lost a lot of pieces. Especially the manual or instructions. I also want to get a charger for home outlet.
-
How to connect and use with a camper trailer and power for home
I would like to use a Yeti 3000 generator with my camper trailer when we are camping without electrical hookup. I have a cord that plugs into a 120 outlet from my my camper. Is this what I would use to plug into the generator. If I plug into the generator with the camper would I be able to use an oxygen machine throughout…
-
YETIX 600W POWER SUPPLY
The User Guide states: NOTE: Not compatible with Yeti Lead Acid, Yeti Lithium, or the Yeti 200X/500X Power Stations. If a Yeti 1500X has one or more Yeti Tank Expansion (Lead Acid) installed, may the YetiX 600W Power Supply still be connected to the Yeti 1500X for charging?
-
Yeti 1500X, Tank Expansion, 600W Power Supply
Can I attach my 600W Power Supply to my 1500X and AT THE SAME TIME attach the 8mm Power Supply to the Link for charging my Tank and additional AGMs? I know that the 600W cripples the 1500X 8mm ports. However, I assume the 8mm Port on the Link is still powered. I don't have this equipment; only doing research prior to…
-
AGM to Lithium Battery
I have a Goal Zero Yeti 1250 and would like to remove the AGM battery I am currently using and eventually replace it with a Lithium battery. Is this plug and play as long as the battery fits inside and can I also use the daisy chain feature and add a second lithium battery.
-
12v outlet
Good day! We have a Yeti 1000 Core that has been put through a lot and performs flawlessly. My question is this, (though I should already know the answer) can the 12v be expanded? Can all of the 12v options be used at the same time. We currently power a fridge/freezer off the “cig” lighter port. We also have a diesel…
-
Connect
Are there cables to connect parallel two 3000? Thank you
-
Yeti Link update to firmware 1.8.4
Hi, i have a Yeti 1500x installed in our cam-ervan with a Yeti Link and a B-to-B charging option. I have just updated the firmware to 1.8.4. The battery/tank lights keep burning, even when I am in CAR mode. This gives a lot of green night during the night Is there a way/trick to switch the green lights off? Eric
-
Yeti 1500X Battery Replacement
The User Guide states: DO NOT tamper with or attempt to replace your battery. For information about a replacement battery contact the Goal Zero solutions center. What is the procedure when a new battery is required?
-
Yeti Link & Lithium Battery - Why Not?
I have extra GZ EC8 to ring cables, so physically, I could easily connect a lithium battery to the link that's installed in my 1500X. Something I often do with extra AGM & other deep cycle batteries I have sitting around. So, what is it about the Yeti Link design or circuitry that prohibits the use of a lithium battery in…