-
What Solar Configuration is required to fully charge 7800WH in 6hrs
I have a Yeti 3000x and 4800WH (4x tanks). The system is off-grid and is my main source of power. I have a Victron charge controller 100/30. I would like to daily recharge the system with about 3500WH. What solar configuration would allow me to achieve this?
-
yeti 6000 for a Rheem gas furnace
I used a KillaWatt to make sure it met all the power requirements, and it seems fine, but when I try to use the Yeti my Furnace gets error code 26, which says it thinks Neutral is wired wrong. Is something wired wrong in the 6000's pure sine wave converter?
-
Wifi off after outage I'm traveling
I'm currently in Thailand and we had a 15+ hour power outage at home in California. Power is back on but I cannot access my yetti 3000x as the software turned off the wifi (to save power). I had the Yeti in hot stand by running the frig, freezer and 2 lighting circuits. Now there is no way for me to know the status of the…
-
Is it possible to use a home integration kit as a primary breaker in an off grid setting?
I’d like to install and power a few wired outlets with my Yeti at my off grid cabin, anyone know if that’s possible with this kit?
-
Home Backup automatic failover?
Maybe I'm not searching the right thing but I can't seem to find out whether a backup battery like the Yeti can be set up to take over automatically when grid power fails. Looks like the HIK that comes with the Home Backup kits is a manual. Does anyone have experience with this or know a reason it may be not feasible?…
-
Can a Yeti 1500X run a gas furnace (fan) with a backup panel?
If I buy a backup sub panel, can my Yeti 1500X power the furnace if the only electric power it uses is the fan? The heat source is gas. It seems logical but I don’t want to buy the backup kit if this won’t work. Thanks.
-
Does the Yeti 6000 act like a UPS and power directly from AC electricity (when available)?
I live in an the Caribbean, where power outages are frequent, from a couple hours a day, to weeks at a time (for a big hurricane). And I travel a lot, so I am not at home to plug in my refrigerator to my Yeti, nor throw the switch on the back up transfer switch. So, I plan to plug my Yeti 6000x into the wall, and plug my…
-
3000X specification question
Does my Yeti 3000X have the following specifications to qualify for my electrical provider's transfer switch requirement for a backup generator? They are offering a free transfer switch for my house but only if my generator (Yeti 3000X) meets or exceeds their specification requirement. This is the required spec: 30A,…
-
Home Integration Kit and AFCI (CAFCI) Circuit Breaker Connection
Great day all. I have a Yeti 3000X and home integration kit, tied to the grid. everything works nice. my issue is that I have CAFCI Circuit breakers in my main panel due to NEC electrical codes. Out of the 4 Circuits from the transfer Switch, one of the powers a circuit that is on a CAFCI breaker, everything works till I…
-
I installed my Yeti S 1500 and 4 tanks today. Want to make sure it's set up correctly.
Does this pic mean I have 28 16??? WH? I purchased the 6300Wh Home Backup System. Did the 4 tank batteries come fully charged? How do I check/know? Home Backup System Update I Held in the "Units" for 7-10 sec, it reset the 1500X to 0, so now how do I check to see if the tanks are functioning? Thanks!
-
Adding yeti home integration kit to existing panels only grid tied solar home
Want to add a yeti and a home integration transfer kit to my existing home to power a few circuits when the power goes out. Any issues or considerations to understand that are caused by the existing solar panels and inverter? I assume that in a power outage if I switch each circuit I want to use from line to gen that is…
-
Plugged in my laptop and ZAP
Earlier today, I plugged my one week old laptop into my Yeti 1000x using USB-C, and the moment the cable was plugged in, there was a POP noise from the laptop. Kinda like a electrical arc zap, if you're familiar with that noise. At the same moment, the laptop turned off. The laptop is now dead and won't turn on at all.…
-
Connecting two Yeti 1000 in parallel to the Home Integration Kit
I have two Yeti 1000s, I would like to use them in parallel with the home integration kit to combine the capacity of both for backup power to my home without having to manual switch from one to the other, when the first one runs out of juice. What would happen if I make/use a combiner cable to combines outputs from both…
-
Plugging in an oxygenator
I am on oxygen 24/7. I have a Yeti 3000X in case the power goes out. A few nights ago the power went out at 3:30 am. Fortunately, I was awake when the power went out and plugged my oxygenator in. That got me to thinking. What if I hadn't been awake? So I thought the best thing to do would be to plug in my oxygenator into…
-
Recommended battery settings for charging Tank with Victron MPPT?
I can't find any information on what would be recommended battery settings for charging a set of (6) Yeti Tanks from solar panels with a "Victron MPPT 100 | 30", i.e. the offical "30-Amp External MPPT" set offered by Goal Zero, in order to avoid over and under charging for extending battery life. I understand that the Tank…
-
1500X/Four Tanks/Link black wire does not fully insert into its slot
I have the 1500X and four tanks. The link expansion module black wire does not fully insert. Is this normal? The system seems to work okay, however recently I needed to reset the system due to some sort of fault.
-
Is it normal for a Yeti 3000X to be constantly charging?
I have a Yeti 3000X. I keep it plugged into the wall and nothing is connected to it. I've noticed that it doesn't charge up to 100%. Instead it somehow runs down to 94% and then recharges. Is there something wrong with my Yeti?
-
Has anyone installed two home integration kits with two Yetis in the same house? 8 circuits.
-
Can the HIK be used to power my rooftop solar panels? There are 20 20 amp circuits.
-
Yeti Link
I have a Yeti 1500X with a Yeti Link and 2 tanks the other day the Link’s lights shut off and it is no longer charging the Tanks. The system is only a month old. Is my Link toast or is there a way to rest it?
-
A/C capable
I see nothing on the site or looking at the strongest unit about the whole house generators being able to run a Central Air conditioning system. Can anyone answer this? I live in hurricane ally S Florida.
-
my 6000 does not read amp vs watts correcly on the output side.
-
can I connect my goalzero into my house, via a A/C house outlet? with or without a inverter?
-
How important is battery cycling
If I'm looking at the 6000x + 4 tank kit for emergency home backup how important it s it to occasionally drain and recharge the tanks? I can imagine using the 6000x in various ways to cycle the battery but if I don't have a power interruption for a long period of time what's the best way to keep the tank batteries healthy?
-
Does anyone have a rough estimate (or experience) of the cost to install the home integration kit?
-
Whole House
Is it possible to run the whole home on a Goal Zero? I am looking for a house backup system and would love to use a Goal Zero. Thank you
-
Watt Hours Readout
I have a Yeti1000x with 4 yeti tanks attached. The readout on the display of yeti1000x shows 1405 Watt Hours, which is equivalent to my Yeti1000x + 1 tank. Why do I not see the watt hours for the remaining tanks?
-
Lack of schematics and explanation of limits
I just bought a 8400 W home backup kit. I also have 4 panels, the Yeti X 600W Power supply, a 4x High Power Port Connector, 2 x 30 foot High Power Port extension cables and 4 x 200 W Boulders. What I am trying to figure out is the limitations on a total cable run. I have read on other posts in the community pages (I…
-
Connecting Nomad200 to Yeti400 lithium
My Yeti1000 won't be here until Monday (I hope) so I want to try our my solar panels. l see there is a different connecter than on my Boulder 50s use so what does the connection require? Thanks, TJ
-
Yeti Home Integration Kit transfer switch
Why is the Yeti Home Integration Kit transfer switch not feasible for an external breaker box? It seems to me that the transfer switch could be on the inside wall opposite of the external breaker box and the wires could go through the wall.